On this page down the page you'll find additional quality points with regards to How to Install a Bathtub.
Setting up a tub isn't specifically rocket science, yet it does need solid plumbing, carpentry, and sometimes, tiling skills. Changing an old bath tub with a brand-new one is also a reasonably difficult task. If the old tub is conveniently accessible, the project can move easily; if you have to open a wall surface to eliminate the old bathtub and position the new bathtub, the job is much harder. In either case, the project is within a house handyman's abilities, although you will need an assistant to move out the old tub as well as embeded in the new one. See to it you have actually certified yourself for the task and are comfortable attempting it. Rather than employing a professional to take control of a halfway-completed job, it is much better to take into consideration utilizing one prior to you start. Opportunities are you may need an expert plumber to make tube links.
This short article will certainly aid you set up a brand-new tub in your shower room if you have currently gotten a brand-new tub and do not need to change the arrangement of your previous supply of water pipes.
Your devices and material checklist ought to make up the following:
Preparing for the Setup
Firstly, the sustaining structure supplied with the bathroom ought to be fitted (if needed) according to the manufacturer's directions. Next off, fit the faucets or mixer to the bathtub. When fitting the faucet block, it is important to make sure that if the faucet features a plastic washing machine, it is fitted in between the bathroom as well as the faucets. On a plastic bath, it is also reasonable to fit a sustaining plate under the taps device to avoid stress on the bathtub.
Fit the versatile tap connectors to the bottom of both taps making use of 2 nuts and olives (sometimes supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the electrical outlet with the hole in the bathroom. Use the nut supplied by the producer to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the versatile overflow pipeline to the overflow electrical outlet. After that, screw the pipe to the overflow face which should be fitted inside the bathroom. See to it you make use of all of the supplied washers.
Attach the catch to the bottom of the waste electrical outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Link all-time low of the overflow tube in a comparable manner.The bath must now be ready to be suited its last setting.
Removing Old Touches
If you need to change old faucets with new ones as a part of your installation, then the first thing you ought to do is disconnect the water system. After doing so, activate the taps to drain pipes any kind of water staying in the system. The procedure of getting rid of the existing faucets can be fairly bothersome as a result of the restricted accessibility that is often the instance.
Utilize a container wrench (crowsfoot spanner) or a tap device to undo the nut that links the supply pipes to the faucets. Have a fabric prepared for the staying water that will originate from the pipes. When the supply pipelines have been eliminated, utilize the exact same tool to loosen up the nut that holds the faucets onto the bath/basin. You will certainly need to quit the solitary taps from turning throughout this procedure. When the taps have actually been eliminated, the holes in the bath/basin will need to be cleansed of any type of old securing substance.
Before carrying on to fit the new taps, contrast the pipe connections on the old taps to the new faucets. If the old faucets are longer than the new taps, after that a shank adapter is required for the brand-new faucets to fit.
Setting up the Bathtub
Making use of both wooden boards under its feet, position the tub in the called for position. The wooden boards are valuable in equally spreading the weight of the tub over the location of the boards instead of focusing all the weight onto 4 little points.
The next goal is to make sure that the bath tub is leveled all round. This can be attained by examining the spirit level and readjusting the feet on the bathtub till the spirit level checks out degree.
To install taps, fit the bottom of the furthest versatile tap port to the suitable supply pipeline by making a compression sign up with; then do the same for the various other tap.
Turn on the supply of water and also check all joints and also new pipework for leakages and also tighten them if essential. Load the bath tub as well as likewise examine the overflow electrical outlet and also the typical outlet for leakages.
Finally, take care of the bath paneling as described in the producer's instruction manual. Tiling and also securing around the tub ought to wait till the tub has actually been used at least once as this will certainly settle it into its last placement.
Fitting New Touches
If the tails of the new taps are plastic, after that you will need a plastic connector to stop damage to the string. One end of the connector fits on the plastic tail of the tap and the various other end supplies a link to the existing supply pipelines.
If you need to fit a monobloc, after that you will require lowering couplers, which connects the 10mm pipe of the monobloc to the standard 15mm supply pipe.
Next off, position the faucet in the mounting hole in the bath/basin ensuring that the washing machines remain in place between the faucet and the sink. Safeguard the tap in position with the supplier supplied backnut. When the faucet is firmly in place, the supply pipes can be linked to the tails of the faucets. The taps can either be connected by utilizing corrugated copper piping or with typical tap adapters. The previous kind must be linked to the tap ends initially, tightening only by hand. The supply pipelines can later be attached to the other end. Tighten up both ends with a spanner after both ends have actually been connected.
Tiling Around the Bathtub
In the area where the bathroom meets the tile, it is necessary to seal the joins with a silicone rubber caulking. This is important as the fitting can relocate sufficient to split a stiff seal, causing the water to penetrate the wall in between the bathroom and the tiling, causing difficulties with moisture and possible leakages to the ceiling below.
You can choose from a variety of coloured sealers to assimilate your components as well as installations. They are sold in tubes and cartridges, and are capable of sealing gaps up to a width of 3mm (1/8 inch). If you have a bigger void to fill, you can load it with spins of soaked newspaper or soft rope. Bear in mind to always load the bathtub with water before securing, to permit the activity experienced when the tub is in usage. The sealer can split fairly early if you do not take into consideration this motion prior to sealing.
Conversely, ceramic coving or quadrant floor tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are likewise easily readily available on the market. It is advisable to fit the floor tiles making use of water-resistant or waterproof adhesive and cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I found that content about How to Install a Bathtub when doing a lookup on the web. Liked our piece of writing? Please share it. Help another person check it out. Thank you for taking the time to read it.
Results guaranteed, contact!